Programmers device > AVR Programmers

USBasp AVR programmer in korpuse

USBasp AVR programmer in korpuse

Features

  • ISP programming interface
  • Interface connection to PC: USB
  • Input voltage: 5V (Bus USB)
  • Dimensions 54x25x9 mm
  • To work under Windows driver needed
Price:
352 грн
Code: 137
шт.
Є в наявності

Переглянути відгуки (0)

USBasp - a simple and convenient programming avr microcontroller interface ISP (serial programming mode). Connects to the USB-port of the computer, which is very convenient since most PCs now no COM- or LPT- ports. Use USBasp programmer function in-circuit programming (ISP) allows you to quickly and repeatedly programmed microcontroller avr, even without removing it from the device. The process of debugging software using this AVR programmer is simple, convenient and saves time.

USBasp. A truly "national" USB-programmer - because of ease of manufacture, ease of circuit and open source, it has become a de facto standard and is supported by a large number of programming tools.
Programmer USBasp only supported programming interface ISP. To work under Windows need a driver (there are ). USBasp protocol is used for many USB-bootloaders (thanks to the openness and simplicity).

List of supported AVR microcontrollers:
USBASP AVR Programmer supports all ATMEL microcontrollers with serial programming mode ISP (In System Programming):

ATtiny11, ATtiny12, ATtiny13, ATtiny15, ATtiny22, ATtiny2313, ATtiny24, ATtiny25, ATtiny26, ATtiny261, ATtiny28, ATtiny44, ATtiny45, ATtiny461, ATtiny84, ATtiny85, ATtiny861
AT90S1200, AT90S2313, AT90S2323, AT90S2343, AT90S4414, T90S4433, AT90S4434, AT90S8515 , AT90S8535
ATmega8, ATmega48, ATmega88, ATmega16, ATmega161, ATmega162, ATmega163, ATmega164, ATmega165, ATmega168, ATmega169, ATmega32, ATmega323, ATmega324, ATmega325, ATmega3250, ATmega329, ATmega64, ATmega640, ATmega644, ATmega645, ATmega6450, ATmega649, ATmega6490, ATmega128, ATmega1280, ATmega1281, ATmega2560, ATmega2561, ATmega103, ATmega406, ATmega8515, ATmega8535
AT90CAN32, AT90CAN64, AT90CAN128
AT90PWM2, AT90PWM2B, AT90PWM3, AT90PWM3B
AT90USB1286, AT90USB1287, AT90USB162 , AT90USB646, AT90USB647
Design:
Connect the programmer to the device is performed using the loop. Naznecheniya ISP connector pins is shown below isp connector pogrammatora usbasp
  1. MOSI (output data)
  2. VCC + 5v (power output for programmable devices from the USB current up to 200ma)
  3. Reset (connected to pin microcontroller reset)
  4. SCK (output timing data)
  5. MOSI (input data for isp programming)
  6. GROUND (minus power, total)
Jumper
When you open the jumper on the SCK frequency increases to 375 kHz, with a closed reduced to 8 kHz. This is done by programming the MC with a frequency below 1.5 MHz. Basically, all the MK factory programmed the system clock to the internal oscillator frequency of 1 MHz, so you need to set the jumper on the programmer
LEDs
Green (yellow) - indicates the operating status of the programmer
Red - indicates that there is an exchange of data between the device and the PC
If you do not have the ability or desire to buy a programmer USBasp, it is possible to collect himself. Descriptions assembly in this article

Reviews of the USBasp AVR programmer in korpuse: