SpeedyBee F405 V3 Flight Stack with ESC 50A 3-6s BLHeli_S 4in1 30x30mm

MCU: STM32F405

IMU(Gyro): BMI270

USB Port: Type-C

Barometer: Built-in

OSD Chip: AT7456E chip

BLE Bluetooth: Supported. Used for setting up the flight controller

DJI Air Unit connection method: Using 6-pin connector or soldering

Blackbox MicroSD Memory Card Support: Yes

BetaFlight Camera Control Panel: Yes

Input current sensor: yes

Input Power: 3S - 6S Lipo

ESC outputs: M1 to M4 on the bottom and M5 to M8 on the top

UART: 6 sets(UART1, UART2, UART3, UART4(for ESC Telemetry), UART6)

ESC: Telemetry UART R5(UART5)

I2C: Supported

Buzzer: is

BOOT button: yes

RSSI input: yes

SmartPort: yes

Firmware support: BetaFlight(Default), EMUFlight, INAV

Target firmware: SPEEDYBEEF405V3

Mounting Diagram: 30.5x30.5mm (4mm hole diameter)

Size: 42mm x 40mm x 8mm

Count			Price
From	1	шт	3185	грн
From	2	шт	3122	грн

Переглянути відгуки (1)

With this product buy:


Brushless motor Emax EcoII 2807 6s 1300kv for Fpv racing drone	Foxeer Micro Cat 3 1200TVL 1/3" CMOS 0.00001lux FPV Camera	AKK FX2 Dominator 250/500/1000/2000mW 5.8GHz video transmitter for 37 channels	Happymodel EP1 RX / EP2 900RX ExpressLRS Receiver	HQProp 7X4X3 PC 7040 Light Gray Three Blade Propellers for FPV Drones	Antenna Rush Cherry FPV 5.8G SMA RHCP 160

DESCRIPTION SpeedyBee F405 flight stack: F405 V3 FC flight controller and 50A 3-6s BLHeli_S 4-in-1 ESC speed controller in 30x30mm. This model with Bluetooth connectivity and setup, has built-in 4-level battery indicators, a 1500 uF filter capacitor, built-in barometer and more.

FEATURES

Dedicated DJI Air Unit connector for quick connectivity 4 x UART for connecting devices: receiver, VTX, camera, GPS SD card slot supports up to 4 GB of Blackbox data

BEC: 9V 2A and 5V 2A 4 LED battery level indicator 8 motor outputs: m1-m8

Built in barometer

Bluetooth control

Note: BOOT button. Usage options:

[A]. Press and hold BOOT button and simultaneously turn on FC to force FC into DFU mode, this is for FC firmware when firmware is lost.

[B]. When the PC is on and in standby mode, the BOOT button can be used to control the LED strips connected to the LED1-LED4 connectors on the underside.

By default, briefly press the BOOT button to switch to LED display mode. Press and hold the BOOT button to toggle between SpeedyBee-LED mode and BF-LED mode. In BF-LED mode, all LED1-LED4 strips will be controlled by the Betaflight firmware.

SpeedyBee BLS 50A 30x30 4-in-1 ESC

Firmware: BLHeli_S JH50

Wireless Configuration: SpeedyBee app support

PC Configurator link: https://esc-configurator.com/

Direct current: 50A x 4

Peak current: 55A(5sec)

TVS Protection: Yes

External Capacitor: 1500uF Low ESR Capacitor(Included)

ESC Protocol: DSHOT300/600

Input Power:3-6S LiPo

Power Out: VBAT

Current Sensor: Yes

Mounting Size: 30.5x30.5mm (4mm diameter holes)

Dimensions: 45.6x44x6.1mm

Weight: 13.8g

COMPLETE

1x SH 1.0mm 30mm 8pin cable (for FC-ESC connection)

1x SpeedyBee F405 V3 Flight Controller - 30x30

1x M3x8mm silicone grommets (for FC)

1x DJI 6pin cable(80mm)

Reviews of the SpeedyBee F405 V3 Flight Stack with ESC 50A 3-6s BLHeli_S 4in1 30x30mm:

Валерій

Дякую. Швидко доставили