Programmers device

Programmer USB-BLASTER

Features:

Support for all programmable logic integrated circuits companies Altera;
is compatible with operating systems: Windows 2000 / XP / Vista, UNIX, and all Linux;
compatible control software: Cyclone II, Quartus II;
Power supply: USB bus 5;
support for programming interfaces: JTAG, Active Serial, Passive Serial;
programming voltage: 1.5 - 5;
support integrated debugger kernel-level NiosII;
Supports logic analyzer SignalTapII;
Two LEDs: Power and COM;
programmer sizes: 56 x 28 x 14 mm;
JTAG loop length: 22 cm;
USB cord length: 43 cm.
datesheet

Count			Price
From	1	шт	196	грн
From	2	шт	187	грн

Programmer AVR USBasp

ISP programming interface
Interface to PC: USB
voltage: 5V (via USB)
dimensions 54x25x9 mm
to work under Windows driver needed

Count			Price
From	1	шт	87	грн
From	4	шт	83	грн
From	18	шт	75	грн
From	33	шт	70	грн

STK500 (AVR-Doper)

Full compatibility c STK500
voltage: 5V (via USB)
Current consumption: less than 50mA
Interface to PC: USB
Interface Programmer: ISP
Dimensions unit: mm 55h17
Supported programming microcontrollers: Series AVR - all controllers with SPI interface for programming.

Count			Price
From	1	шт	196	грн
From	2	шт	187	грн

AVR ISP MK2

AVRISP MKII programmer
Loop 10 pin
podklyuchynyya Cable to PC USB TIP A

Price:

336 грн

Programmer PICKit3

Interface HID.
Support for Windows 7 system.
Full speed 12 Mbit / s over USB
How to debug in real time
MPLAB IDE compatible (free copy included)
Built-in over-voltage / short circuit monitor
Ability to update the firmware to the PC download from the Internet
Supports voltage range (2 - 6v)
Diagnostic LEDs (power, busy, error)

Count			Price
From	1	шт	532	грн
From	2	шт	506	грн

Programmer PICkit 2

USB 2.0 (USB Type A)
OS Compatibility - Win98 / 2000 / XP / Vista / Se7en
Ability to power from the USB programmable device computing system
Function USB-UART converter
Function Logic Analyzer
High Voltage Programming
The calibration function is constant RC oscillator
Firmware microcontroller simply pressing a button on the programmer
Update firmware via USB Programmer
Official support software from Microchip MPLAB IDE and PICkit 2 Programmer
LED power ON Power (green)
The status LED R / W (red)
Miniature size 83h30 mm

Price:

420 грн

Programmer ST-Link V2

Features:
Support controllers STM32 with SWD debug interface controllers with support STM8 SWIM debug interface
The programmer is powered from 5V USB connector
Standard USB-mini connector
SWD interface to work with ARM CORTEX
Support Connection Full Speed USB 2.0

Count Price
From 1 шт 196 грн
From 2 шт 187 грн
Code: 60
шт.

USB logic analyzer Saleae Logic 24MHz 8ch

Features:
8 input channels;
Logical Tally;
Input: 5PF, 100K ohms;
USB power supply;
The sampling rate can be set as shown below:
24MHz. 16 MHz, 12 MHz, 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz, 200 kHz, 100 kHz, 50 kHz, 25 kHz;
Download data in real time, max. The depth of the collection of 10 tons, from a practical necessity.

Price:
224 грн
Code: 67
шт.

DIP BOARD AVR

Possibility to connect external quartz
supply selection of programming microcontroller
Sockets for DIP-40, DIP-28, DIP-14, DIP-8, DIP-20
User guide ICSP DIP BOARD

Count Price
From 1 шт 392 грн
From 2 шт 373 грн
From 5 шт 338 грн
Code: 24
шт.

Count	Price
From	1	шт	392	грн
From	2	шт	373	грн
From	5	шт	338	грн

AVRISP mkII

clone programmer AVRISP-MKII
supports all microcontrollers Attiny, Atmega and Xmega
Programming Interfaces:

ISP (in-circuit programming)
PDI (interface for programming and debugging)
TPI (interface for programming ATtiny).

PC communication - USB
supply selection is programmable 3.3 microns or 5 volts

Count Price
From 1 шт 504 грн
From 2 шт 479 грн
From 5 шт 434 грн
From 9 шт 404 грн
From 22 шт 363 грн
Code: 26
шт.
assemble your own

Count	Price
From	1	шт	504	грн
From	2	шт	479	грн
From	5	шт	434	грн
From	9	шт	404	грн
From	22	шт	363	грн

JTAG ICE Emulator debugger programmer for Atmel

Fully compatible with AVR Studio
Working with 3 .. + 5V debugging device
Support for breakpoints
Programming flash, EEPROM, fuse bits, lock bits
USB interface for programming and debugging.
Jumper to select the USB converter to UART TTL (when installing the jumper function is blocked and the debugger is switched mode converter)
AVR JTAG ICE takes the + 5V power directly from the USB port. It is possible to supply + 5V 350mA from the USB port to debug the device, eliminating the need for an external power supply.
Ability to update the firmware AVR JTAG ICE directly from AVR Studio
LED "Power filed"
The indicator "Debug"
Compatible with Windows 98/2000 / XP / Linux / MacOS

Price:
336 грн
Code: 104
шт.

USBasp AVR programmer in korpuse

Features

ISP programming interface
Interface connection to PC: USB
Input voltage: 5V (Bus USB)
Dimensions 54x25x9 mm
To work under Windows driver needed

Count Price
From 1 шт 224 грн
From 2 шт 213 грн
Code: 137
шт.

Count	Price
From	1	шт	224	грн
From	2	шт	213	грн

STK500 adapter AVRISP USBASP

Features:

10-pin ISP interface - for connecting to the programmer;
6-pin ISP interface - to connect to the ICSP interface microcontroller;
Dimensions: 34.5 x 20.3 x 8.5 mm;
Weight: 3 g

Price:
56 грн
Code: 144
шт.

The adapter 40 pin ICSP ZIF Programmer PICkit 2 (PICkit 3)

Features:

Direct connection type (no wires)
Type DIP adapter universal
Compatible with chips in buildings: DIP6, DIP8, DIP14, DIP16, DIP20, DIP24, DIP28, DIP32, DIP40.
Lead Spacing: 2,54mm.
The distance between the rows of pins: 5 mm to 17.5 mm.

Price:
140 грн
Code: 158
шт.

Adapter socket TQFP32 QFP32 LQFP32 to DIP28

Features:
Type: TQFP32, QFP32, LQFP32 to DIP28 IC programmer adapter;
Landing site: a socket of 28 pins for installing the chip in the TQFP32, QFP32, LQFP32;
Support for ATMEGA8, ATMEGA8A, ATmega328;
The pitch is 0.8 mm (0.031 inches), 4 pairs of contacts are 7x7 mm;
Dimensions of the adapter (L x W x H): 43x35x30 mm;
Package weight: 49g.

Count Price
From 1 шт 504 грн
From 2 шт 479 грн
Code: 1051
шт.

Count	Price
From	1	шт	504	грн
From	2	шт	479	грн

Programmer AVR USBasp + Zif Board 40pin for AVR

Features Programmer AVR USBasp:

ISP programming interface
Interface connection to PC: USB
Input voltage: 5V (Bus USB)
Dimensions 54x25x9 mm
To work under Windows driver needed

Features Zif Board for AVR:

Weight: 46 g
Size: 88mm x 38mm
32 I / O pins all withdrawn.
Support chips: ATMEGA16 / ATMEGA32 and compatible.
Reset: reset button.
Power LED (D1).
Standard ISP.

Price:
252 грн
Code: 318
шт.

PicKit 3 programmer + ZIF-board for the PICkit 2 (PICkit 3)

Features PicKit 3 programmer:

Interface HID.
Support for Windows 7 system.
Full speed 12 Mbit / s over USB
How to debug in real time
MPLAB IDE compatible (free copy included)
Built-in over-voltage / short circuit monitor
Ability to update the firmware to the PC download from the Internet
Supports voltage range (2 - 6v)
mode - Programmer-to-Go - autonomous controllers programming PIC programs up to 512K bytes;
Diagnostic LEDs (power, busy, error)
Features ZIF-board for the PICkit 2 (PICkit 3):

Direct connection type (no wires)
Type DIP adapter universal
Compatible with chips in buildings: DIP6, DIP8, DIP14, DIP16, DIP20, DIP24, DIP28, DIP32, DIP40.
Lead Spacing: 2,54mm.
The distance between the rows of pins: 5 mm to 17.5 mm.

Price:
672 грн
Code: 316
шт.

PicKit 2 programmer + ZIF-board for the PICkit 2 (PICkit 3)

Features PicKit 2 programmer:

USB 2.0 (USB Type A)
OS Compatibility - Win98 / 2000 / XP / Vista / Se7en
Ability to power from the USB programmable device computing system
Function USB-UART converter
Function Logic Analyzer
High Voltage Programming
The calibration function is constant RC oscillator
Firmware microcontroller simply pressing a button on the programmer
Update firmware via USB Programmer
Official support software from Microchip MPLAB IDE and PICkit 2 Programmer
LED power ON Power (green)
The status LED R / W (red)
Miniature size 83h30 mm
Features ZIF-board for the PICkit 2 (PICkit 3):

Direct connection type (no wires)
Type DIP adapter universal
Compatible with chips in buildings: DIP6, DIP8, DIP14, DIP16, DIP20, DIP24, DIP28, DIP32, DIP40.
Lead Spacing: 2,54mm.
The distance between the rows of pins: 5 mm to 17.5 mm.

Price:
560 грн
Code: 317
шт.

Programmer AVR USBasp + Zif board 28 pin for Atmega8 ATmega48 ATMEGA88

Features Programmer AVR USBasp:

ISP programming interface
Interface connection to PC: USB
Input voltage: 5V (Bus USB)
Dimensions 54x25x9 mm
To work under Windows driver needed

Features Zif board 28 pin for Atmega8 ATmega48 ATMEGA88:

Support chips: Atmega8 ATmega48 ATMEGA88
Reset: Reset button
Power LED (D1)
Standard: ISP
The fee is 7.4 cm x 3.4 cm
The thickness of the module: 1.6 mm.

Price:
196 грн
Code: 659
шт.

AVRISP mkII programmer

Characteristics:

Compatibility: AVR Studio (4.12 and later)
Interface: ISP
Support for Programming Flash and EEPROM
Support for microcontrollers with a supply voltage from 1.8 V to 5.5 V
Adjustable programming speed: 50 Hz to 8 MHz
USB: 2.0 (Full-speed, 12 Mbit / s)
Power supply: USB bus, no external power supply
Protection front lines of programmable devices, including Short circuit.

Price:
896 грн
Code: 704
шт.

CH341A USB Programmer

Features USB Programmer CH341A:

chip 8pin / 16pin
Model CH341A
a series of programmable chips 24hh (I2C) and 25xx (SPI)

Count Price
From 1 шт 168 грн
From 2 шт 160 грн
Code: 863
шт.

Count	Price
From	1	шт	168	грн
From	2	шт	160	грн

Clip SOIC8 SOP8

Clip SOIC8 SOP8 allows you to program different kinds of chips in packages SOIC8 SOP8. Adpter BIOS / 24/25/93.

Price:
112 грн
Code: 876
шт.

Programmer - hardware and software apparatus for recording / reading information in read-only memory ( ROM internal memory MCU ) . Select the type of programmer

programmer is essential when working with microcontrollers . According to the complexity
If
radio fan to quickly and easily program the microcontroller device , you can use a simple programmer that connects to the COM- or LPT-port of the computer. For example , the easiest microcontroller programmer for AVR - is a cable of six wires and four resistors (called a programmer Gromov ) .
For amateurs who develop software for microcontrollers, there are more sophisticated programmers . Sometimes they contain a microcontroller . Such switches are convenient because after flashing MK transfer their outputs in Z-state , and the device can be programmed to test without disconnecting the programmer. With self- manufacture of this type of programming can be " chicken and egg problem " - if the programmer uses a microcontroller circuit , then it must be programmed in the absence of ready made programmer . To solve it, have to make the simplest programmer to connect to the COM- or LPT-port of the computer.
By connecting chips

parallel .
-circuit .
Parallel programmers contain a slot in which is inserted and a programmable microcontroller .
In-Circuit Programmers are suitable for those types of microcontrollers that support in-system programming . They allow you to flash the microcontroller without removing it from the device.
When connected to a computer programmers can be used :

serial port.
parallel port .
specialized interface card (ISA or PCI).
USB.
Ethernet.
Modern switches are connected via USB. Only simple inexpensive models using COM- or LPT- ports. Industrial programmers mainly use Ethernet.
Advanced Features

availability of drivers for popular operating systems ( most often - Windows and Linux).
Validation connect the programmer to program the microcontroller.
JTAG- adapters are used simultaneously for programming and debugging programs for MC.
ability to perform one-touch so-called automatic programming, ie a sequence of operations. For example, to erase , erase verify , record , verify the record and set the configuration fuse- bits .