GreenChip.com.ua
Models aircraft > Flight controllers

Flight Stack SpeedyBee F7V3 BL32 50A 30x30mm

Flight Stack SpeedyBee F7V3 BL32 50A 30x30mm

  • FEATURES
  • Supports BetaFlight (default), EMUFlight flight controller firmware
  • SmartPort - utilizes any UART transmit pad for SmartPort function.
  • BLE support used to customize the flight controller.
  • Full slot DJI Air Unit JST on board
  • WiFi support - used for transferring data such as firmware
  • Download button - used to quickly enter DFU mode
  • RSSI input
  • WS2812 LEDs
  • WiFi/Bluetooth capabilities
  • Size: 45mm x 40mm x 16mm
    • Count Price
    From1шт6860грн
    From2шт6723грн
    Code: 1864
    шт.

    Бесплатная доставка по Украине

    Є в наявності
    Переглянути відгуки (0)
    recommended products:
    SpeedyBee F7V3 Flight Stack BL32 50A 30x30mm

    SpeedyBee F7V3 flight stack includes F7V3 flight controller and BL32 50A 128K 4in1 ESC. Equipped with a BMP280 barometer, on-screen menu, 500MB blackbox, built-in charge monitoring and many other features. This stack will be the perfect addition to your FPV build.

  • CHARACTERISTICS

    Processor: STM32F722

    Gyroscope: MPU6000

    Barometer: BMP280 (I2C)

    OSD: BetaFlight OSD with AT7456E chip

    Built-in BlackBox flash memory: 500Mb

    BetaFlight camera control panel: Yes

    Power consumption: 3S - 6S LiPo

    UART port: full UART x 5 (UART1, UART2, UART3, UART5, UART6)

    ESC telemetry: UART UART4 RX

    ESC signal pads: M1-M4 on the back side and M5-M8 on the front side

    I2C bus: is there, SDA and SCL pads on the front side, used for external magnetometer, sonar, etc.

    Support WS2812 LED modules: yes

    Support beeper: yes, 5V (BZ+ and BZ- pads)

    RSSI input: Yes

    Interface: USB-C

    DJI Air Unit slot: Yes

    Firmware: BetaFlight

    Firmware Target: SPEEDYBEEF7V3

    IMU: BMI270

    USB: Type-C

    Mounting Diagram: 30.5 x 30.5mm, hole size M4

    Dimensions: 41 x 38 x 8.1mm

    Weight: 10.7g

    SpeedyBee BL32 50A 4in1 ESC speed controller

  • Firmware: SpeedyBee BL32 50A

    Wireless Configuration: SpeedyBee App Support

    PC Configurator link: http://github.com/bitdump/BLHeli/releases

    DC current: 50A x 4

    Peak current: 55A(5sec)

    TVS protection: Check

    Radiator: Check

    External Capacitor: 1500uF Low ESR Capacitor(included)

    ESC Protocol: DSHOT300/600

    PWM Frequency: 16KHz-128KHz

    Input Power: 3-6S LiPo

    Output Power: VBAT

    Current Sensor: Yes

    Mounting size: 30.5x30.5mm (hole diameter 4mm)

    Dimensions: 45.6x40x8.8mm

    Weight: 19.2g (with heatsink)

  • COMPLETION

    F7 V3 FC

    1 x SpeedyRee F7 V3 Flight Controller

    1 x DJI 6pin Cable(80mm)

    1 x SH 1.0mm 30mm-length 8pin Cable(for FC-ESC connection)

    5 x M3*8mm Silicone Grommets(for FC)

    1 x 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable(30mm) (A)

    1 x 4pin SH1.0 to 3+2pin JST1.25 FPV Cam Cable(60mm) (B)

    1 x 4pin SH1.0 to 4pin JST1.25 FPV Cam Cable(60mm) (C)

    1 x 4pin SH1.0 Radio Receiver Cable(100mm) (D)

    1 x 4pin SH1.0 to 4pin SH1.0 Analog VTX Cable (E)

    1 x 6pin SH1.0 GPS Module Cable without Connector on other end(100mm) (F)

    1 x 6pin SH1.0 GPS Module Cable Connector of another end (G)

  • BL32 50A 4in1 ESC

    1x SpeedyRee Speed Controller BL32 50A 4in1 ESC

    1x 35V 1000uF Low ESR Capacitor

    5x M3x8.1mm silicone bushings (for ESC)

    5x M3x8.1mm silicone o-rings

    1x SH 1.0mm 30mm 8pin cable(for FC-ESC connection)

    1x XT60 power cable(70mm)

    Flight Stack 23 Flight Stack 2 Flight Stack 1
    • Reviews of the Flight Stack SpeedyBee F7V3 BL32 50A 30x30mm: