Others > CNC machine tools

TB6600 stepper motor controller

TB6600 stepper motor controller

Characteristics:
  • Type: TB6600
  • Control circuit Supply voltage: 4.5-5.5 In
  • The supply voltage of the power unit: 8-50 in
  • The maximum operating current: 5 A
  • The maximum switching frequency: 200 kHz
  • microstepping modes: 1/1, 1/2, 1/4, 1/8, 1/16
  • Size: 8 x 5 x 3.5 cm
  • Weight: 118.3 g
Count Price
From1шт484грн
From2шт470грн
Code: 651
шт.
Є в наявності

TB6560 stepper motor driver

TB6560 stepper motor driver

Characteristics:
  • Power supply: 10 - 35 V DC
  • Opto-isolated input control signals
  • Current: 0.3 - 3 A, 3.5 A peak
  • divider step (microstep): 1, 2, 8, 16
  • Protection: Low voltage, over temperature and over-current
  • Operating temperature: -10 ~ 45 ℃
  • size: 75 x 50 x 33 mm
  • Weight: 83 g
Count Price
From1шт396грн
From2шт385грн
From7шт373грн
Code: 649
шт.
Є в наявності

Engine  for CNC 17HS4401

Engine for CNC 17HS4401

  • Model: 17HS4401
  • Type: Hybrid
  • The number of phase 2
  • Current consumption: 1.7 A
  • Soprostivlenie: 1.5 ohms
  • The holding time: 4 kg * cm
  • The moment of inertia of the rotor: 54gr * cm2
  • Step: 1.8 ° (200 steps per revolution)
  • Weight: 0.28 kg
Count Price
From1шт748грн
From2шт726грн
Code: 33
шт.
Є в наявності

BL-MACH-V1.1 to control the CNC machine

BL-MACH-V1.1 to control the CNC machine

  • Voltage digital supply (V) - 5V DC
  • Supply voltage power section (B) - 12-24 V DC
  • The maximum current consumption of digital part - 500mA
  • Relay switching capacity - 10A / 24V AC
  • Declared minimum number
  • positives relay under load - 500 million cycles
Count Price
From1шт352грн
From2шт342грн
From7шт331грн
From13шт324грн
Code: 887
шт.
Є в наявності

TB6600 stepper motor controller

TB6600 stepper motor controller

Characteristics:
  • Type: TB6600
  • Control circuit Supply voltage: 4.5-5.5 In
  • The supply voltage of the power unit: 8-50 in
  • The maximum operating current: 5 A
  • The maximum switching frequency: 200 kHz
  • microstepping modes: 1/1, 1/2, 1/4, 1/8, 1/16
  • Size: 8 x 5 x 3.5 cm
  • Weight: 118.3 g
Price:
528 грн
Code: 924
шт.
Є в наявності

Motor Driver 10 - 60

Motor Driver 10 - 60

Characteristics:
  • Power supply motor: 10-60V
  • Power supply circuits: 5
  • Output current: less than 100 mA
  • Protection current: 0-20 A (default - 15 A)
  • PWM control input signal: 3-20 in
  • Protection: short circuit, overcurrent
  • Customize soft start: 0-5 (default - 2.5 c)
Count Price
From1шт1980грн
From2шт1921грн
Code: 647
шт.
Є в наявності

Bearing for CNC

Bearing for CNC

Features:

  • Model: KP08
  • Material: zinc alloy
  • inner diameter: 8 mm
  • base: (L * W) 5.5 * 1.3 cm
  • total height: 2.8 cm
  • external diameter pulley: 2.5 cm
  • Weight: 50gr
Price:
132 грн
Code: 964
шт.
Є в наявності

A4988 stepper motor driver module + heatsink

A4988 stepper motor driver module + heatsink

Characteristics:
  • Built on a chip: A4988  
  • Power supply circuits logic: 3.3 - 5.5  
  • Supply voltage motors 8 - 35  
  • The maximum current per channel: 1 (without additional cooling) to 2 A (with cooling)  
  • Adjust the maximum value of the motor output current  
  • Built-in protection against overheating and overloading  
  • Five step size options: 1 step, 1/2 step, 1/4 step, 1/8 step, 1/16 step (microstep)
Price:
114 грн
Code: 648
шт.
Є в наявності

Engine  for CNC 17HS8401

Engine  for CNC 17HS8401

  • Model: 17HS8401
  • Type: Hybrid
  • The number of phase 2
  • Current consumption: 1.8 A
  • Soprostivlenie: 1.8 ohms
  • The holding time: 5.38 kg * cm
  • Step: 1.8 ° (200 steps per revolution)
  • Weight: 0.37 kg
Price:
748 грн
Code: 921
шт.
Є в наявності

CNC machine T 3020-D300

CNC machine T 3020-D300

Features:

  • Machine dimensions: 560 * 450 * 450 mm
  • Rack material: 6061 and 6063 hard aluminum alloy
  • Engraving area: X300: Y200: Z60 (the engraving depth depends on the length of the cutting edge) mm
  • Allowable material thickness: ≤60mm
  • Rail type: chrome shaft + linear bearings 61HRC
  • Screw type: trapezoidal 1404 with double thread
  • Spindle motor: 300W / 12000r / min noise
  • Collet type: ER11, 3.175 mm
  • Stepper motor and drive: two-phase hybrid stepper motor, 3A / PHASE, 150N. Cm, 8 segments of the disk.
  • Maximum working speed: 4000 mm / min (engraving speed: 300-3000 mm / min)
  • Positioning accuracy: 0.03 mm
  • Communication interface: parallel port (It is necessary to use a desktop computer, does not support a laptop)
  • Software compatibility: Mach3 / Emc2 / Kcam, (Type3, Wentai, ArtCAM, coppercam)
  • Command code: G code. Nc). Ncc /. Tab /. Txt
  • Machine weight: 25 kg
    Price:
    35200 грн
    Code: 994
    шт.

    Бесплатная доставка по Украине

    Є в наявності

    CNC Shield version 3.0

    CNC Shield version 3.0

    Features: Payment CNC Shield version 3.0
    • Model - CNC Shield version 3.0;
    • Size - Arduino UNO and other compatible boards;
    • Axles - 4 (X, Y, Z, A);
    • The supply voltage of the logic - 5;
    • The supply voltage of the power unit - 12 - 36;
    • Drivers - A4988 or DRV8825 and others;
    • Interfaces - UART, I2C;
    • Firmware - Arduino GRBL;
    • Dimensions - 65 x 55 x 20 mm;
    • Weight - '32
    Price:
    572 грн
    Code: 922
    шт.
    Очікуєм