TinySA spectrum analyzer with 4" display from 100 kHz to 5.3 GHz and 32 GB memory card

* Input frequency range from 100 kHz to 350 MHz

* Input impedance of 50 ohms when input attenuation is set to 10 dB or more

* Selectable manual and automatic input attenuation between 0 dB and 31 dB in 1 dB increments

* Absolute maximum input level without attenuation +10 dBm

* Absolute maximum input power with 30 dB attenuation +20 dBm for a short period

* Input signal interception point for third-order modulation products (IIP3)) with 0 dB attenuation +15 dBm

* 1 dB compression point at +2 dBm with 0 dB attenuation

* Power detector resolution of 0.5 dB and linearity from frequency +/-1 dB

* Absolute power level accuracy after power level calibration +/- 1 dB

* Lowest detectable signal using a 30 kHz resolution bandwidth with -102 dBm

* Frequency accuracy is equal to the selected resolution bandwidth

* Phase noise -90 dB/Hz at 100 kHz offset and -115 dB/Hz at 1 MHz offset

* Dynamic range without pulses when using 30 kHz bandwidth at 70 dB resolution

* Manually selectable resolution filters, 3, 10, 30, 100, 300, 600 kHz Automatic selection of one of 57 resolution filters.

* Screen resolution of 145 or 290 measurement points.

* Scanning speeds of over 1000 points/second using the highest resolution filters.

* Automatic optimization of actual scan points to ensure coverage of the entire scan range regardless of the selected resolution band

* Pulse suppression option to evaluate whether certain signals are internally generated or actually present in the input signal

* Input frequency range from 240 MHz to 960 MHz.

* Since there is no input bandpass filter, strong signals outside the 240 MHz to 960 MHz range may cause distortion of in-band signals

* Absolute maximum unattenuated input level of +10 dBm

* Input intercept point for third-order modulation products (IIP3) -5 dBm

* 1 dB compression point at -6 dBm with 0 dB attenuation

* Power detector resolution of 0.5 dB and linearity against frequency +/-1 dB

* Absolute power level accuracy after power level calibration +/- 1 dB

* Lowest detectable signal using a 30 kHz resolution bandwidth of -115 dBm

* Frequency accuracy is equal to the selected resolution bandwidth

* Dynamic range without pulses when using the 30 kHz resolution bandwidth 50 dB

* Selectable (automatic and manual) 3, 10, 30, 100, 300 and 600 kHz resolution filters

* Additional 25 dB to 40 dB input attenuation depending on frequency. Power level error with activated attenuator increases to +/- 15 dB

* Screen resolution of 145 or 290 measurement points.

* Scan speeds of over 1000 points/second using the highest resolution filters.

* Automatic optimization of the actual scan points to ensure coverage of the entire scan range regardless of the selected resolution bandwidth

* Sinusoidal output with harmonics below -40 dB fundamental

* Output frequency range from 100 kHz to 350 MHz

* Output level selection in 1 dB steps between -76 dBm and -6 dBm

* Optional AM, narrow FM and wide FM modulation or slow sweep in a selectable frequency range

* Square wave output.

* Output frequency range from 240 MHz to 960 MHz

* Output signal level can be selected in variable steps between -38 dBm and +13 dBm

* Optional narrow FM modulation or wide FM modulation or slow sweep in selectable frequency range

* Optional square wave output with -25 dBm fundamental level connected to high I/O

* The frequency can be set to 1 MHz, 2 MHz, 4 MHz, 10 MHz, 15 MHz or 30 MHz.

* Charging time max. 1 hour via USB port or USB charger minimum 500 mA

* Operation from a fully charged battery for at least 2 hours

2.8" TinySA spectrum analyzer * 1

sma-sma rg174 radio cable 20 cm * 2

USB Type-C data cable *1

Hand rope *1

SMA mother-to-mother connector *1

SMA telescopic antenna *1